View this video for steps you can take to troubleshoot. Check the main gas valve to see if the gas is fully operational.
If you don’t have a chimney cap, an animal may have built a nest in your chimney, causing blockage.
Gas fireplace won't start after summer. First, shut off the gas feed and wait for a few minutes. Hold the pilot button down for a couple of minutes to purge out any trapped air. If your furnace won't turn on at all, you'll want to check the circuit breakers that service its power source.
If the pilot light isn’t on even when the fire of the fireplace is still running, you will have to take some simple measures. Flipped on the wall switch, took a minute or two and then fired up. Trouble getting your gas fireplace started?
If gas is coming out of the pilot, but it still won't light, the spark igniter could be the problem. This will make sure that there is no excess gas built up in the system. If playback doesn't begin shortly, try restarting your device.
Here are some potential causes: If your gas fireplace has an electronic ignition check or replace the fuse. Double check that the gas is actually on if your gas fireplace isn’t working correctly.
You should never just rush to the gas valve and start twisting it. How to troubleshoot a gas fireplace. If you’re smelling gas, then shut it off.
1) make sure the gas is on. If these check out, it could be overloaded fuses or breakers, an obstruction, a gas pressure issue, moisture in the gas line, or clogged burner ports. Each time you start your gas fireplace, you’ll notice some condensation on.
Try to turn the wall switch on. First, take a look at the main valve to confirm that the gas is on. If gas is reaching the fireplace, but it still won’t light, the next step is to light the gas jets on the gas logs, manually, following the manufacturer’s instructions.
Here are some steps to take if your gas fireplace is on the fritz. You may also want to examine. There are several issues that might prevent a gas fireplace from igniting.
Gas fireplace with the pilot always on, has a hole with key in it on the floor right next to fireplace (based on prior answers thats for gas supply), a ‘light’ switch across the room that when flipped on basically turns the flames on and entire fireplace lights up, then a knob next to the light switch that when turned clockwise increase the. Below are some common problems with gas fireplaces and how to fix them: If the batteries in either of.
The pilot flame should look like a small, sharp blue flame, like a small blowtorch. Sometimes this is an easy way to fix a gas fireplace that won’t turn on. Why won’t my gas fireplace start?
There are several issues that might prevent a gas fireplace from igniting. If your fireplace isn’t starting, follow these steps. Seems simple, but the gas valve could have gotten turned off for any number of reasons over the summer or since it was last used.
We often have that problem in the showroom over the summer, particularly with units we don’t turn on very often; If your home was hit by a lightning strike or other power surge over the summer, it's possible the circuit breaker tripped without tipping you off, especially if your furnace is in the basement or another area you don't frequently visit. Bought the house this summer, and got the pilot light lit when fall came.
Perhaps it is already on, but the gas hasn’t been ignited in awhile. While if it is on a breaker, turn the breaker all the way off and then back on again. 1) make sure the gas is on.
↑we have an annual maintenance contract for our gas fireplace. So i suggest you look carefully at the condition of the pilot flame for the likely source of your problem. Keeping your fireplace on a single breaker will ensure that your fireplace won’t trip a breaker, or blow a fuse.
The glass on my fireplace looks smudged. Without any gas, your fireplace won’t be able to light. There are several reasons a chimney doesn’t provide enough of a draft.
We’ll set the remote to act as a thermostat over the winter, and then in the summer, the fireplace keeps automatically turning itself off! Alleyne says to look for and clear out any debris between the igniter and thermocouple. We used to turn off the pilot light during the summer months, but then were told to leave it on as it would prevent spiders from nesting in it.
However, if you don't start the fireplace for say months, like during the summer months, when you do attempt to start it again, it takes well over a minute, sometimes over two minutes. After turning it on, wait a couple minutes, and then try lighting the fireplace again. After a few minutes, the pilot is supposed to light up.
Make sure the gas is on. If the pilot light isn’t on even when the fire of the fireplace is still running, you will have to take some simple measures. Depending on the type of gas fireplace you own, you may have a remote or receiver that run on batteries.
It also suggests that the problem is in the ignition system. Videos you watch may be added to the tv's watch history and influence tv recommendations. And the most common reason why a gas fireplace wont light when the switch is turned on is a dirty pilot burner.
We started to do so after the tech had difficulty restarting it. The most common of these are wood fireplaces, but gas ones have their own set of advantages that make them real popular as well. If there isn’t enough of a draft in the chimney, it’s difficult to get a fire going due to lack of oxygen.
The gas supply to the fireplace may have been turned off during the summer months. Fireplaces are great centerpieces that can bring style and class to just about any room. If the gas fireplace pilot light is on but won’t start check that your gas valve is turned on and check the fuse or breakers.
Gas fireplace won't start after summer. If you run the fireplace frequently, say like every day or every few days, the fireplace starts within seconds after turning on the wall switch.